Myacide™ AS Technical by BASF is a white to pale yellow, free flowing, crystalline solid. It contains inherently biodegradable 2-bromo-2-nitropropane-1,3-diol. Acts as a biocide. Offers biocidal... view more

Myacide™ AS plus by BASF is an inherently biodegradable 2-bromo-2-nitropropane-1,3-diol grade used as a biocide. Offers biocidal performance alone or in combination with other actives. Used in... view more

Protectol™ BN 98 by BASF is an inherently biodegradable 2-bromo-2-nitropropane-1,3-diol used as a biocide. Offers biocidal performance alone or in combination with other actives. Used in water-based... view more

acResin® ZeroPCF A 204 UV by BASF is an UV cross-linkable, biocides-, MOSH-, MOAH- & solvent-free, high-performance acrylic hot-melt polymer. Exhibits very good shear-, good- tack & peel properties, excellent... view more

Corona™ 9 by Croda is skin-friendly, water in oil emulsion stabilizer that reduced tackiness. It is a scratch-resistant and anti-blocking additive. It prevents scarring on the surface, especially at... view more

Maxemul™ 5010 by Croda is a non-ionic, co-polymerizable surfactant for use as a stabilizer in latex binders typically used in pressure-sensitive adhesives. It is reactive towards vinylic unsaturated... view more

Zephrym™ PD 2246 by Croda is a polymeric dispersant. It offers enhanced dispersion viscosity and extended storage capability. It is recommended for both organic and inorganic pigments including... view more

Finntalc M15 by Elementis is floated, medium sized, laminar talc (Mg-silicate). It is recommended for adhesives and polyester putties... view more

Finntalc M30 by Elementis is floated, coarse, laminar talc (Mg-silicate). It is recommended for adhesives and polyester putties... view more

Finntalc M40 by Elementis is floated, coarse, double air classified, laminar talc (Mg-silicate). It shows low oil absorption. It is recommended for adhesives and polyester putties... view more

Finntalc M50 by Elementis is floated, very coarse, double air classified, laminar talc (Mg-silicate). It shows low oil absorption. Finntalc M50 is recommended for adhesives and polyester putties... view more

Finntalc M65 by Elementis is talc (Mg-silicate). It is recommended for adhesives and polyester putties... view more

Jeffamine® M-2095 Amine by Huntsman is polyethylene glycol (PEG)-based polyetheramine. It is a hydrophilic polyether monoamine of approximately 2000 molecular weight. Exhibits moderate viscosity... view more

Jeffamine® M-3085 Amine by Huntsman is a hydrophilic polyether monoamine of approximately 3000 molecular weight with a PO/EO mole ratio of about 8/58. Exhibits moderate viscosity and low vapor... view more

Omnirad 4MBZ Flakes by IGM Resins is an effective Type II photoinitiator. Used in combination with tertiary amine synergists to initiate radical polymerization of unsaturated oligomers such as acrylates after... view more

Cariflex™ IR0307 K by KRATON is a solution polymerized polyisoprene with a high cis-1,4 content. It exhibits high molecular weight. It is used as a replacement for natural rubber in a wide range of... view more

Cariflex™ IR0310 K by KRATON is a solution polymerized polyisoprene with a high cis-1,4 content. It possesses high molecular weight. It is used as a replacement for natural rubber in a wide range of... view more

Polymeg 2000 Polyol by LyondellBasell is polytetramethylene ether glycols (PTMEG) produced by polymerizing tetrahydrofuran. The chain is capped with primary hydroxyl units. At slightly elevated... view more

1,10- Decanediamine by Mitsui Chemicals acts as a curing agent for epoxy resin. It offers excellent wet resistance and mechanical properties. 1,10- Decanediamine is listed with TSCA inventory... view more

1, 12-Dodecanediamine by Mitsui Chemicals is a curing agent for epoxy resin. It offers excellent wet resistance and mechanical properties. 1,12- Dodecanediamine is listed with TSCA inventory... view more